top of page

What Do 4/4, 5/4, 6/4, and 8/4 Mean in Hardwood Lumber?

35 minutes ago
4 min read

Shopping for hardwood lumber can introduce an unfamiliar set of numbers. Instead of seeing thickness described only in inches, buyers encounter labels such as 4/4, 5/4, 6/4, and 8/4.


These designations are part of the quarter-inch system used to describe hardwood thickness. Understanding them helps prevent ordering mistakes, makes supplier listings easier to interpret, and allows better planning for the material removed during milling.


The basic idea is straightforward: each “quarter” represents one-quarter of an inch of nominal rough thickness. The important detail is that this designation does not necessarily describe the board’s current measured thickness.


Understanding the Quarter-Inch System


Hardwood thickness is commonly expressed as the number of quarter-inch increments in its nominal rough thickness.

Designation

Spoken as

Nominal rough thickness

4/4

Four-quarter

1 inch

5/4

Five-quarter

1¼ inches

6/4

Six-quarter

1½ inches

8/4

Eight-quarter

2 inches

The arithmetic is simply the first number divided by four. Five quarters equal 1¼ inches, and eight quarters equal 2 inches. Hardwood suppliers use these names to identify thickness categories, even after some material has been removed through surfacing.

Nominal Thickness vs. Actual Thickness


Nominal thickness is the thickness category used to describe the lumber. Actual thickness is what the board measures now. Those measurements can differ because lumber changes during drying and loses material during surfacing. A rough board also needs enough extra thickness to allow saw marks and irregularities to be removed.


For example, a supplier may offer 4/4 hardwood surfaced to 13/16 inch. The board is still described as 4/4 because that is its rough-thickness category, but its current thickness is 13/16 inch. Depending on the project and condition of the stock, additional milling may bring it to ¾ inch.


The quarter designation and the measured thickness therefore answer different questions. One identifies the material category; the other tells you what is available for your project.


What Thickness Can You Expect After Surfacing?


Suppliers commonly offer surfaced hardwood at dimensions below the nominal rough thickness. The following are useful examples, not guaranteed finished dimensions:

Designation

Nominal rough thickness

Common supplier-surfaced thickness

4/4

1 inch

13/16 inch

5/4

1¼ inches

1 1/16 inches

6/4

1½ inches

1 5/16 inches

8/4

2 inches

1¾ inches

Supplier practices vary. Some offer different surfaced thicknesses, and individual boards may require additional work before they are flat and ready for a project. Always confirm the actual thickness being sold rather than relying on a general chart.


Why Milling Removes More Than Saw Marks


Preparing a board is not always just a matter of smoothing its surface. A rough board may have cup, bow, or twist. Creating a flat reference face can require removing material from its higher areas. The opposite face is then brought parallel to that reference face at the desired thickness. The more correction a board needs, the less thickness may remain.


Length also affects the challenge. Obtaining a flat component from a long, bowed board can require a different allowance than obtaining a shorter component from a suitable section of that same board.


For this reason, the nominal rough measurement is not a promise of final yield. The condition of the stock and the dimensions of the required parts matter.


What Is 4/4 Lumber Used For?


Four-quarter lumber is a common starting category for general furniture and cabinetry components where a finished thickness near ¾ inch is appropriate.

Examples might include cabinet parts, furniture panels, rails, and smaller project components. Suitability still depends on the design, species, span, and intended use.


If a plan requires a full 1-inch finished thickness, ordinary 4/4 stock is generally not the right assumption. Once the board is surfaced and flattened, there is usually not enough material left to retain that full inch.


The purchasing question should be, “What rough stock will yield my required finished thickness?” rather than, “Which label matches the finished number?


When Does 5/4 Make Sense?


Five-quarter lumber provides more thickness than 4/4 without moving to the next heavier category. It is often considered when a project requires a finished component around 1 inch thick. However, that result depends on the board’s actual starting measurement and how much correction it requires.


A buyer might also choose 5/4 to provide additional milling allowance for a thinner finished component. Whether that is worthwhile depends on availability, price, board condition, and the project’s requirements.


What About 6/4 and 8/4?


Six-quarter and eight-quarter stock provide starting thicknesses for more substantial components. They may be considered for thicker furniture parts, legs, selected tabletop designs, turning stock, or material intended for resawing. These are possible applications, not automatic recommendations for every project. For example, an 8/4 label does not promise a finished 2-inch tabletop. Surfacing removes material, and flattening may remove more.


Thickness Designations Do Not Describe the Whole Board


A quarter designation describes thickness—not width, length, grade, or surface preparation. A 4/4 board may be rough-sawn, partially surfaced, or fully machined. Boards in the same thickness category may also be sold in different widths and lengths.


Before ordering, clarify:

  • Actual current thickness.

  • Surface preparation.

  • Available widths and lengths.

  • Whether dimensions are rough or finished.

  • Any dimensional tolerances relevant to the project.


Start With the Finished Part


The most reliable buying process begins with a cut list. Identify the finished thickness of each component, then allow for the work required to produce it. Consider whether the stock is rough or surfaced, whether further flattening is necessary, and whether the available boards provide a reasonable margin.


Buying unnecessarily thick lumber increases material cost and milling work. Buying too thin can make the planned component impossible.


Understanding the quarter system helps strike that balance. The label identifies where the board begins as a commercial thickness category; the actual measurement and condition determine what it can become.


The Bottom Line


Four-quarter, five-quarter, six-quarter, and eight-quarter describe nominal rough thicknesses of 1 inch, 1¼ inches, 1½ inches, and 2 inches. The essential buying lesson is that nominal rough thickness is not the same as current or final thickness. Confirm the supplier’s measurements, work backward from the finished part, and leave an appropriate allowance for preparation.

 
 
 

Recent Posts

See All

Comments


bottom of page